|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Magnesium matrix composite reinforced by nanoparticles-A review显示文摘Significant progress has been made in magnesium-based composites during recent decades,especially for the appearance of magnesium matrix composite reinforced by nanoparticles.The nanoparticles added not only exhibit a good strengthening effect,but also maintain the initial toughness of the matrix,effectively balancing the contradiction between the strength and plasticity in the traditional magnesium matrix composites.The magnesium matrix nanocomposites with excellent mechanical properties have pushed the development of magnesium matrix composites to a new stage.However,it is very difficult to disperse the nanoparticles in metal melt especially in magnesium melt which is different from other metal melts and dangerous during the cast processing.This means that the preparation of magnesium matrix nanocomposite is extremely challenging.Further,the magnesium matrix nanocomposites possess a distinctive characteristic in deformation behavior,strengthening and toughening mechanism due to their special size effect of nanoparticles.Accordingly,this review will focus on the new preparation technologies,deformation behavior,mechanical properties and strengthening and toughening mechanisms.The potential applications,development trends and future research ideas of magnesium matrix nanocomposite are also prospected.©2020 Published by Elsevier B.V.on behalf of Chongqing University. | K.B.Nie X.J.Wang K.K.Deng X.S.Hu K.Wu | 2021 | Journal of Magnesium and Alloys2021，9，1： | 12 |
| 2 | Processing, Microstructure and Mechanical Properties of Ti6Al4V Particles-Reinforced Mg Matrix Composites显示文摘Novel Ti6Al4V particles-reinforced AZ91 Mg matrix composites were successfully fabricated by stir casting method. The stirring time in semisolid condition directly affected the particle distribution and the quality of the ingots.Furthermore, the optimal speed of the heating and the liquid stirring could overcome particle settlement caused by the density difference between the matrix and the particles. Ti6Al4V particles distributed uniformly in the composites with different particle contents. The average grain size decreased with the increase in the particle contents. The Ti6Al4V particles bonded pretty well with the alloy matrix. In addition, there were some interfacial reactions in the composites.There were rod-like Al_3Ti phases at the interface. The precipitates extended from the particle surface to the matrix, and they might improve the interfacial bonding strength. The ultimate tensile strength, yield strength and elastic modulus were enhanced as the particle contents increased, and the elongation was much better than that of the same matrix material reinforced with SiC particles. Thus, the novel composites exhibit better comprehensive mechanical properties. | X.M.Wang X.J.Wang X.S.Hu K.Wu M.Y.Zheng | 2016 | Acta Metallurgica Sinica(English Letters)2016，29，10： | 5 |
| 3 | A Novel Melt Processing for Mg Matrix Composites Reinforced by Multiwalled Carbon Nanotubes显示文摘Carbon nanotubes(CNTs) reinforced Mg matrix composites were fabricated by a novel melt processing.The novel processing consisted of two courses:CNTs pre-dispersion and ultrasonic melt processing.Mechanical ball-milling was employed to pre-disperse CNTs on Zinc(Zn) flakes.Serious CNT entanglements were well dispersed to single CNT or tiny clusters on Zn flakes.The ultrasonic melt processing further dispersed CNTs in the Mg melt,especially tiny CNT clusters.Thus,a uniform dispersion of CNTs was achieved in the as-cast composites.Hot extrusion further improved the distribution of CNTs.CNTs increased both the strength and elongation of the matrix alloy.Notably,the elongation of the matrix alloy was enhanced by 40%.Grain refinement and the pulling-out of CNTs resulted in the evident improvement of ductility for the composites. | H.L.Shi X.J.Wang C.L.Zhang C.D.Li C.Ding K.Wu X.S.Hu | 2016 | Journal of Materials Science & Technology2016，32，12： | 3 |
您所在的机构暂未开通此部分的功能，请联系管理员