|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Review on the Application of Bamboo-Based Materials in Construction Engineering显示文摘Due to the continuously increasing demand for building materials across the world,it is necessary to use renewable materials in place of the existing nonrenewable materials in construction projects.Bamboo is a fast-growing flowering plant that may be used as a renewable material in construction.The use of bamboo in the construction of buildings can improve its long-term carbon fixation capacity and economic benefits.Although bamboo has the advantages of superior performance,low carbon content,high energy-saving and emission-reducing capacity,bamboo is an anisotropic material,which has many factors affecting its material performance,large variability of material performance,lack of systematic research,and the use of bamboo as the main building material is not always limited.This paper systematically summarizes the research status of bamboo as a building material from the aspects of bamboo composition,gradation,material properties,bamboo building components,connection nodes,and use of artificial boards.On this basis,some constructive suggestions are put forward for the further study of bamboo in the field of architecture. | Biqing Shu Zhongping Xiao Lu Hong Sujun Zhang Chen Li Naiqiang Fu Xiaoning Lu | 2020 | Journal of Renewable Materials2020，8，10： | 2 |
| 2 | Effect of Steam Explosion Technology Main Parameters on Moso Bamboo and Poplar Fiber显示文摘One of the large-scale industrial applications of Moso bamboo and poplar in China is the production of standardized fiberboard.When making fiberboard,a steam blasting pretreatment without the addition of traditional adhesives has become increasingly popular because of its environmental friendliness and wide applicability.In this study,the steam explosion pretreatment of Moso bamboo and poplar was conducted.The steam explosion pressure and holding time were varied to determine the influence of these factors on fiber quality by investigating the morphology of the fiber,the mass ratio of the unexploded specimen at the end face,the chemical composition,and the tensile strength.The following conclusions were drawn:As the steam burst pressure and holding time increased,more cellulose and hemicellulose degradation occurred(the degradation of hemicellulose was greater than that of cellulose),the lignin content rose,and the fiber bundle strength decreased.The degradation of bamboo cellulose was slightly higher than that of poplar,and the degradation of poplar hemicellulose was significantly faster than that of bamboo.Furthermore,increasing the steam explosion pressure and pressure holding time could not effectively increase the lignin content.It is recommended to use a steam blasting pressure of 2.5 MPa or 3.0 MPa and a holding time of 180 s to perform steam blasting on bamboo and poplar specimens. | Biqing Shu Qin Ren Lu Hong Zhongping Xiao Xiaoning Lu Wenya Wang Junbao Yu Naiqiang Fu Yiming Gu Jinjun Zheng | 2021 | Journal of Renewable Materials2021，9，3： | 1 |
| 3 | Study on the Bonding Performance of the Moso Bamboo Dowel Welded to a Poplar Substrate Joint by High-Speed Rotation显示文摘The wood friction welding technique with its high bonding strength,low cost,high efficiency,and without any adhesive has been increasing concern in China.Moso bamboo(Phyllostachys pubescens)and poplar(Populus sp.)are widely planted and used in the furniture industry,interior decoration,and wood structure construction in China.The aim of this work was to investigate the bonding performance of moso bamboo dowel rotation welded joints with different dowel/receiving hole diameter ratios.The results indicated that the ratio of dowel/receiving hole diameter was an important parameter that influenced the welding performance.The bonding strength of the bamboo-to-poplar welded joints at the optimal ratio of 10/7 was as high as 7.50 MPa,which was higher than that of the beech(Fagus sylvatica,L.),schima(Schima superba)dowels and PVAc glued joints.The temperature measurement results showed a peak temperature of bamboo dowel welding as high as 350–360°C.Some differences in the temperature curves between each dowel/hole diameter ratio group were observed at the three different hole depths,such as the friction time,peak temperatures,and stabilization time at the maximum temperature,which could explain the differences in welding strengths between different ratios.The SEM results showed the temperature-induced softening,melting and flowing of cell-interconnected polymer material in the wood and bamboo structure.In addition,the bamboo fibers(mainly vascular bundles)were wrapped to form a dense continuous bonding layer,similar to the reinforced concrete,thus producing a good bonding effect.The Fourier transform-infrared spectroscopy(FT-IR)analyses showed that the high temperature resulted in the increase of the lignin relative content due to the degradation reaction of cellulose in the welding zone,which improved the bonding properties. | Suxia Li Haiyang Zhang Biqing Shu Liangsong Cheng Zehui Ju Xiaoning Lu | 2021 | Journal of Renewable Materials2021，9，7： | 1 |
| 4 | Study on the Tangential Tensile Mechanical Properties of Moso Bamboo显示文摘In this work,we used tensile tests to analyze the tangential failure forms of raw bamboo and determine a relationship between tangential tensile strength,elastic modulus,position,density,and moisture content.We found that the tangential mechanical properties of the culm wall were mainly dependent on the mechanical properties of the basic structure of the thin wall.Formulas for calculating the tangential tensile strength of moso bamboo and adjusting the moisture content were also determined.The tangential tensile strength and the tangential tensile modulus of elasticity(TTMOE)followed:outer>middle>inner,and diaphragm>bamboo node>culm wall.Below the fiber saturation point,the tangential tensile strength and TTMOE values of the bamboo gradually decreased with increasing moisture content.When the moisture content was 15%,the tangential tensile strengths of the inner,middle,outer,culm wall,bamboo node,and diaphragm samples of the five-year-old moso bamboo were 3.17,3.29,3.31,3.24,3.67,and 8.85 MPa,respectively.Furthermore,their TTMOE values were 215.09,227.98,238.45,224.04,267.21,and 559.27 MPa,respectively.Hence,this study provides a theoretical basis for future research on bamboo cracking. | Biqing Shu Lu Hong Suxia Li Yupeng Tao Jianxin Cui Naiqiang Fu Junbao Yu Chen Li Xiaoning Lu | 2022 | Journal of Renewable Materials2022，10，8： | 1 |
| 5 | Improving the Properties of Fast-Growing Chinese Fir by Vacuum Hot Pressing Treatment显示文摘Chinese fir was compressed by vacuum hot pressing and conventional hot pressing at different temperatures(180℃,200℃ and 220℃),respectively.The color parameters of the heat-compressed sample were measured,the relative mechanical properties of the material were tested and changes in the chemistry of fir were investigated using Fourier transform infrared spectroscopy(FTIR)and Xray photoelectron spectroscopy(XPS).The results indicated that the color difference between compressed and untreated wood increased gradually with the increase of temperature.Compared with the conventional hot pressing treatment,the color difference(ΔE*)of the Chinese fir treated by vacuum hot pressing decreased by 43.73%,69.91%,and 77.17%,respectively.The mechanical properties(bending elastic modulus and bending strength)of Chinese fir treated by vacuum hot pressing were significantly improved.The 24-hour water absorption thickness expansion rate of fir treated by vacuum hot pressing is smaller than that of conventional hot pressing.It is implied that vacuum hot pressing treatment is an effective method to produce compressed wood,which can improve the mechanical properties and dimensional stability of wood,and reduce the influence of carbonization on wood color. | Lu Hong Biqing Shu Qian He Zehui Ju Haiyang Zhang Xiaoning Lu | 2021 | Journal of Renewable Materials2021，9，1： | 0 |
| 6 | Hydrophobic Poplar Prepared via High Voltage Electric Field(HVEF)with Copper as Electrode Plate显示文摘In order to improve hydrophobic characteristics which will affect the service performance of fast-growing poplar due to growing bacteria in the humid environment.In this study,a simple method was proposed to treat poplar via the high voltage electric field(HVEF)with copper as the electrode plate.Scanning electron microscope(SEM),Fourier transforms infrared spectroscopy(FTIR),X-ray diffraction(XRD)and contact angle tester were adopted to evaluate the surface morphology,surface group of poplar,crystallinity and wettability under HVEF.It was found by SEM that a large number of copper particles were uniformly attached to the surface of poplar.In all three sections,the weight percentage of the Cu element was accounting for more than half.The diffraction peaks of copper-containing compounds appeared in the(XRD).FTIR analysis confirmed that the reaction between copper and poplar took place.The surface contact angle of three sections of poplar increased in the following order:cross section | Jianxin Cui Zehui Ju Lu Hong Biqing Shu Xiaoning Lu | 2022 | Journal of Renewable Materials2022，10，11： | 0 |
| 7 | Experimental Study of Mode-I and Mode-II Interlaminar Fracture Characteristics of Poplar LVL显示文摘Fracture is a common failure form of poplar laminated veneer lumber(LVL).In the present work,we performed an experimental study on the mode-I along-grain interlaminar fracture,mode-I cross-grain interlaminar fracture,and mode-II interlaminar fracture of poplar LVL.We investigated stress mechanisms,failure modes,and fracture toughness values of the different fracture types.The experimental results revealed that the crack in the mode-I along-grain interlaminar fracture specimen propagated along the prefabricated crack direction,and the crack tip broke.The mode-I cross-grain interlaminar fracture specimen had cracks in the vertical direction near the prefabricated crack.In the mode-II interlaminar fracture specimen,cracks appeared along the initial prefabricated crack direction.The load–displacement curves of these three specimens were linear in the early stage of loading.With the increase in the load,a nonlinear segment appeared before crack propagation and a descending segment appeared after crack propagation.The nonlinear segments of the mode-I along-grain interlaminar fracture and mode-II interlaminar fracture were very short,and cracks expanded quickly after their initiation,resulting in brit-tle fracture.The nonlinear segment of the mode-I cross-grain interlaminar fracture was long,resulting in plastic failure.The average toughness values of the mode-I along-grain interlaminar fracture,mode-I cross-grain inter-laminar fracture,and mode-II interlaminar fracture were 15.43,270.15,and 39.72 MPa·mm^(1/2),respectively. | Zhongping Xiao Chen Li Biqing Shu Shukai Tang Xinghuan Yang Yan Liu | 2023 | Journal of Renewable Materials2023，11，1： | 0 |
| 8 | Structure Design and Properties of Three-Layer Particleboard Based on High Voltage Electrostatic Field(HVEF)显示文摘In this study,the effects of three different particle sizes of wood wastes(A=–8+12 mesh;B=–12+20 mesh;C=–20+30 mesh)and factory shavings(D)on the properties of particleboard were investigated.According to the test results,three-layer particleboard was designed.Particleboard face layers made with mixture of A,B,and C.The core layer made with D.The ratio of core layer to face layers is 50:50.Three-layer particleboard were fabricated with 12%urea-formaldehyde(UF)resins and three different high voltage electrostatic field intensities(0 kv,30 kv,60 kv).The internal bond(IB)strength,modulus of rupture(MOR),modulus of elasticity(MOE),thickness swelling(TS),and water absorption(WA)of particleboard were evaluated.The density distribution of the three-layer particleboard were examined by vertical density profiles(VDP),and the bonding mechanism and functional groups changes in the particles were analyzed by FTIR analysis.The results showed that HVEF treatment intensity play a remarkable role in properties of particleboard.The particleboard with higher electrostatic field intensities treatment has higher MOE,MOR,IB,and TS.Under HVEF treatment(60 kv),the MOR,modulus of MOE,and IB of three-layer particleboard were 23.61 N/mm^(2),2787.09 N/mm^(2),and 0.86 N/mm^(2),respectively.FTIR indicated that the surface activity of wood particles was increased electric field treatment. | Man Yuan Lu Hong Zehui Ju Wenli Gu Biqing Shu Jianxin Cui Xiaoning Lu Zhiqiang Wang | 2021 | Journal of Renewable Materials2021，9，8： | 0 |
您所在的机构暂未开通此部分的功能，请联系管理员